自動上料攪拌車工作量大，用戶只要具備一定的專業維修知識，對使用會有很大幫助。不過，機械漏油是很常見的問題，今天就教大家這些小技巧。

The automatic loading mixer has a large workload. As long as the user has some professional maintenance knowledge, it will be very helpful to use. However, mechanical oil leakage is a very common problem. Today I will teach you these tips.

過度使用和油封是正常磨損情況。解決方法：更換新油封即可。

Overuse and oil seals are normal wear conditions. Solution: replace the oil seal with a new one.

長時間不更換機油，濾芯質量不合格，機油太臟，加速油封磨損。解決方法：盡快更換液壓油和濾芯。

If the engine oil is not changed for a long time, the filter element quality is unqualified, and the engine oil is too dirty, which accelerates the wear of the oil seal. Solution: replace the hydraulic oil and filter element as soon as possible.

傳動軸平衡失效，擺動大，造成主軸擺動油封偏磨。解決方法：及時糾正并更換轉軸。

The balance of the transmission shaft fails, and the swing is large, causing the eccentric wear of the main shaft swing oil seal. Solution: correct and replace the rotating shaft in time.

液壓油變質乳化，導致潤滑性能下降，加速油封磨損。解決方法：盡快更換液壓油和濾芯，嚴重時需要清洗系統。

The deterioration and emulsification of hydraulic oil leads to the decline of lubrication performance and accelerates the wear of oil seal. Solution: replace the hydraulic oil and filter element as soon as possible, and clean the system in serious cases.

泵支架松動，開泵，泵固定螺栓松動，進而引起液壓泵整體振動和油封磨損。解決方法：經常檢查和排除自動上料攪拌車可能出現的故障，防止和避免故障。

When the pump support is loose, the pump is opened, and the pump fixing bolts are loose, which will cause the overall vibration of the hydraulic pump and the wear of the oil seal. Solution: frequently check and eliminate the possible faults of the automatic feeding mixer truck to prevent and avoid faults.

自動上料攪拌系統回油不暢，回油管和散熱器堵塞，進而導致電機殼內壓力升高，造成油封漏油。解決方法：清除堵塞物，保持回油循環通暢。

The oil return of the automatic feeding and mixing system is not smooth, and the oil return pipe and radiator are blocked, which leads to the pressure rise in the motor housing, causing oil leakage of the oil seal. Solution: remove the blockage and keep the oil return circulation smooth.

如果散熱器不散熱，油溫過高，粘度和潤滑性下降，油封過熱，密封失效。解決方法：對散熱器進行故障排除，對系統進行冷卻過程，避免泵電機磨損。嚴重時，停止發動機并熄火，用水沖洗泵電機和散熱器外殼，以達到冷卻效果。

If the radiator does not dissipate heat, the oil temperature is too high, the viscosity and lubricity are reduced, the oil seal is overheated, and the seal fails. Solution: troubleshoot the radiator and cool the system to avoid wear of the pump motor. In case of serious condition, stop the engine and shut down, wash the pump motor and radiator housing with water to achieve cooling effect.

冬季啟動自動上料攪拌車如果預熱不足，會導致油溫過低，油和油封達不到理想的工作溫度。解決方法：開機時將油箱停機并怠速運轉10～20分鐘，待油溫正常后再將油箱轉入工作。

If the preheating of the automatic feeding mixer truck is insufficient in winter, the oil temperature will be too low, and the oil and oil seal will not reach the ideal working temperature. Solution: shut down the oil tank and idle for 10 ~ 20 minutes when starting up, and turn the oil tank into operation after the oil temperature is normal.

自動上料攪拌車液壓泵軸端油封是易損件。如果嚴格按照相關規范操作，很多漏油現象會得到有效防止。如果出現漏油問題，要冷靜地找出具體原因，進行處理。更多相關內容就來關注我們http://www.www.boy7up.cn吧！

The oil seal at the shaft end of the hydraulic pump of the automatic feeding mixer is a vulnerable part. If the operation is strictly in accordance with the relevant specifications, many oil leaks will be effectively prevented. In case of oil leakage, find out the specific causes calmly and deal with them. Pay more attention to us http://www.www.boy7up.cn Come on!