自上料攪拌車是一種用于運輸施工混凝土的專用卡車；由于其形狀，它也經常被稱為蝸?？ㄜ??？ㄜ嚥捎脠A柱形攪拌筒運輸攪拌好的混凝土。在運輸過程中，攪拌筒保持轉動，以確?；炷敛荒獭；炷吝\輸完畢后，通常用水沖洗攪拌筒內部，以防止硬化的混凝土占用空間，減少攪拌筒的體積。

The self loading mixer is a special truck for transporting construction concrete; Because of its shape, it is often called a snail truck. The truck uses a cylindrical mixing drum to transport the mixed concrete. During transportation, the mixing drum shall be kept rotating to ensure that the concrete will not set. After the concrete is transported, the interior of the mixing drum is usually washed with water to prevent the hardened concrete from occupying space and reduce the volume of the mixing drum.

攪拌罐是攪拌車的核心部件，技術含量高。由于其技術含量會直接影響混凝土的質量，因此攪拌罐的設計要求精度高，公差范圍小。攪拌槽內的葉片采用雙對數螺旋設計，經實際試驗和模擬修正后才能使用。

The mixing tank is the core component of the mixer truck, with high technical content. Because its technical content will directly affect the quality of concrete, the design of mixing tank requires high precision and small tolerance range. The blades in the mixing tank adopt double logarithmic spiral design, which can only be used after actual test and simulation correction.

攪拌槽內的葉片可提高混凝土的卸料性能。出料口前的葉片上有孔洞，可降低混凝土對葉片的粘結性能，提高出料的均勻性。整個葉片從攪拌罐底部的滑動角度不斷增加，以確保葉片能充分攪拌混凝土，降低殘留率。

The blades in the mixing tank can improve the discharge performance of concrete. There are holes on the blades in front of the discharge port, which can reduce the bonding performance of concrete to the blades and improve the uniformity of discharge. The sliding angle of the entire blade from the bottom of the mixing tank is continuously increased to ensure that the blade can fully mix the concrete and reduce the residual rate.

攪拌罐的材質一般為耐磨高強度鋼板。攪拌罐成型后，拆下內支架，焊接葉片。葉片材料一般采用高耐磨鋼，混合質量與出料速度完美結合。焊接工藝采用碳氧化物保護膜，攪拌罐制作后進行噴丸處理，消除焊接和制作過程中產生的應力，提高鍍層的附著力。

The mixing tank is generally made of wear-resistant high-strength steel plate. After the mixing tank is formed, remove the inner support and weld the blades. The blade is generally made of high wear-resistant steel, and the mixing quality is perfectly combined with the discharge speed. The welding process adopts carbon oxide protective film. After the fabrication of the stirring tank, shot blasting is carried out to eliminate the stress generated during welding and fabrication and improve the adhesion of the coating.

另外，車輛的日常自檢還是需要多加注意的，比如駕駛習慣、行車、起步、剎車等；車輛底盤、車橋及定位，重心是否偏移等。液壓件工作，冬季防凍措施；坦克工作；遠程節氣門供油工作；輪胎：輪胎氣壓測定，滿載輪胎的承重測定；輪胎重點放在海綿路段，磨損情況。

In addition, more attention should be paid to the daily self inspection of vehicles, such as driving habits, driving, starting, braking, etc; Vehicle chassis, axle and positioning, whether the center of gravity is offset, etc. Anti freezing measures for hydraulic parts in winter; Tank work; Remote throttle oil supply operation; Tire: tire pressure measurement, load-bearing measurement of fully loaded tires; Focus on the sponge section of the tire, and the wear condition.

在使用過程中，攪拌車應盡量平穩啟動，緩慢勻速行駛，并經常檢查液壓系統管路和軸承部件的使用情況。建議使用同一品牌的油品，不同廠家生產的油品標準不同。混合后潤滑脂難以清洗、堵塞，增加故障風險，運行穩定，經常維護，仔細檢查。

In the process of use, the mixer shall be started as smoothly as possible, run at a slow and uniform speed, and frequently check the use of hydraulic system pipelines and bearing components. It is recommended to use the same brand of oil products, and the standards of oil products produced by different manufacturers are different. After mixing, the lubricating grease is difficult to clean and block, which increases the risk of failure. It operates stably and is maintained frequently and checked carefully.

快速認識自上料攪拌車的攪拌槽部件使用的相關內容就是這樣了，您可以關注我們的網站www.www.boy7up.cn來咨詢了解更多更新更詳細的信息！

This is how to quickly learn about the use of the mixing tank components of the loading mixer. You can follow our website www.zkzsljbc Com for more updates and more detailed information!