自上料攪拌車的底盤上的零部件也很多，減震器這個部件大家應該都比較熟悉，減震器是用來抑制彈簧吸振后反彈是的震蕩及來自路面的沖擊。在攪拌車的行駛過程中減震器一般都會有響聲，這是因為減震器與鋼板彈簧、車架或軸相互碰撞，膠墊損壞或是減震器防塵筒變形，油液缺乏等原因引起的，怎么判斷減震器是否良好呢？

There are also many parts on the chassis of the self loading mixer. Everyone should be familiar with the shock absorber. The shock absorber is used to suppress the vibration of the spring rebound after vibration absorption and the impact from the road. The shock absorber usually makes a noise during the driving of the mixer truck, which is caused by the collision between the shock absorber and the leaf spring, the frame or the shaft, the damage of the rubber pad, the deformation of the shock absorber dust cylinder, the lack of oil and other reasons. How to judge whether the shock absorber is good?

如果攪拌車的減震器失效或者出現問題，應先查看減震器是否有漏油現象，用力按下保險杠，然后松開，假如攪拌車有兩到三次的騰躍，就說明減震器是好的。

If the shock absorber of the mixer truck fails or has problems, you should first check whether the shock absorber has oil leakage, press the bumper hard, and then release it. If the mixer truck jumps twice or three times, it means that the shock absorber is good.

攪拌車在緩慢行駛中緊急制動，此時如果車輛的振動比較厲害，就說明減震器有問題，需要拆下減震器將其直立，并把下端銜接環夾在臺鉗上，用力拉壓減震桿數次，此時應有穩定的阻力，往上拉的阻力應大于向下的阻力，如果阻力不穩定或無阻力，可能是減震器內部缺油或閥門零件損壞，應終止修復或更換零件，并應立即送去維修。車

The mixer truck is in emergency braking during slow driving. At this time, if the vibration of the vehicle is relatively severe, it indicates that there is a problem with the shock absorber. It is necessary to remove the shock absorber and put it upright, clamp the lower connecting ring on the bench vice, and pull and press the shock absorber rod several times. At this time, there should be stable resistance. The upward resistance should be greater than the downward resistance. If the resistance is unstable or there is no resistance, it may be the lack of oil in the shock absorber or the damage of valve parts, Repair or replacement of parts should be terminated and sent for repair immediately. vehicle

自上料攪拌車減震器漏油一般是以下幾個原因：

The oil leakage of shock absorber of self loading mixer truck is generally caused by the following reasons:

1.減震器內部的清潔度不夠好，有焊渣、鐵屑等雜物導致油封磨損。

1. The internal cleanliness of the shock absorber is not good enough, and there are welding slag, iron filings and other sundries, which lead to the wear of the oil seal.

2.減震器的工作條件比較惡劣，外部的泥沙等雜物進入油封，導致其磨損漏油。

2. The working conditions of the shock absorber are relatively poor, and the external sediment and other debris enter the oil seal, causing its wear and oil leakage.

3.減震器油封的唇口老化，失去了密封的功能。

3. The lip of the shock absorber oil seal is aging and loses its sealing function.

4.可能是在噴底盤裝甲的時候，減震器沒有遮擋好，裝甲附在減震器活塞桿上導致油封磨損而漏油。

4. It may be that when spraying chassis armor, the shock absorber was not covered well, and the armor was attached to the piston rod of the shock absorber, resulting in oil leakage due to wear of the oil seal.

5.控制活塞運動的支桿需要在金屬管的一端延長出來，所以這個部位必須得密封嚴密，一般的漏油都和密封不嚴有直接關系的。

5. The supporting rod controlling the movement of the piston needs to be extended at one end of the metal pipe, so this part must be sealed tightly. Generally, oil leakage is directly related to the lax sealing.

6.一般攪拌車的液壓的減震器漏油就說明它的使用年限已到。

6. The oil leakage of the hydraulic shock absorber of the general mixer indicates that its service life has expired.

攪拌車底盤的減震器是非常重要的，很多人在做保養的時候都容易忽略它，希望看了這篇文章，大家能夠對減震器引起重視。更多相關內容就來我們網站http://www.www.boy7up.cn進行咨詢吧。

The shock absorber of the mixer chassis is very important, and many people tend to ignore it when doing maintenance. I hope you can pay attention to the shock absorber after reading this article. Come to our website for more relevant content http://www.www.boy7up.cn Consult.