如今的攪拌設備已經成為眾多行業中不可缺少的一部分，是建筑工地不可缺少的設備，那么您要想更好的使用它就要在平常中提前預防好故障的出現，比如攪拌設備皮帶零件出現松動怎么辦呢？

Today's mixing equipment has become an indispensable part of many industries and construction sites. If you want to use it better, you must prevent the occurrence of faults in advance. For example, what if the belt parts of mixing equipment become loose?

攪拌設備電機傳動皮帶過松的情況，只需停機后調整攪拌設備電機傳動皮帶的張緊度即可。攪拌設備驅動各種物料在貯罐進行攪拌，它由取力器、萬向軸、液壓泵、液壓馬達、操縱閥、液壓油箱及冷卻裝置組成。

If the motor drive belt of the mixing equipment is too loose, just adjust the tension of the motor drive belt of the mixing equipment after shutdown. The mixing equipment drives various materials to mix in the storage tank. It is composed of power take-off, universal shaft, hydraulic pump, hydraulic motor, control valve, hydraulic oil tank and cooling device.

攪拌設備超載而造成攪拌軸停轉，只需調整進料量，卸出多余的物料，降低攪拌軸轉動負荷即可。

If the mixing equipment is overloaded and the mixing shaft stops running, just adjust the feeding amount, unload the excess materials and reduce the rotating load of the mixing shaft.

側葉片與關內壁卡滯物料時，在攪拌軸停轉前往往會有尖銳刺耳的摩擦聲，出現這種情況時，需立即停機檢查，人工排除異物，重新調整攪拌設備攪拌葉片或側葉片與罐內壁間的間隙，有必要時可以用水先清洗下。

When materials are stuck between the side blade and the inner wall of the tank, there is often a sharp and harsh friction sound before the mixing shaft stops running. In this case, it is necessary to stop the machine immediately for inspection, manually remove foreign matters, readjust the gap between the mixing blade or the side blade of the mixing equipment and the inner wall of the tank, and clean it with water if necessary.

1、檢查V型皮帶是否過松；

1. Check whether the V-belt is too loose;

2、檢查電機皮帶輪與減速機皮帶輪是否在同一水平面上；

2. Check whether the motor pulley and reducer pulley are on the same horizontal plane;

3、檢查減速機皮帶輪與輸入軸的配合間隙是否過大；

3. Check whether the fit clearance between the reducer pulley and the input shaft is too large;

4、檢查減速空載和負載運行是否有異響判斷輸入、輸出軸軸承損壞或內部齒輪是否損壞；

4. Check whether there is abnormal noise during deceleration no-load and load operation, and judge whether the input and output shaft bearings are damaged or the internal gears are damaged;

5、檢查減速機扭矩臂安裝位置是否與減速機軸線垂直；

5. Check whether the installation position of the torque arm of the reducer is perpendicular to the axis of the reducer;

6、檢查驅動滾筒與減速機的同軸度；

6. Check the coaxiality between the drive drum and the reducer;

7、檢查小型攪拌車的軸承是否損壞。

7. Check whether the bearing of the small mixer is damaged.

這些都是攪拌設備零件松動情況下具體原因的分析與解決方法，如果大家在使用攪拌設備的過程中出現故障的話一定要及時的解決才行，特別是類似皮帶零件松動這種問題時才是需要及時解決的。更多相關信息獲取就來我們網站http://www.www.boy7up.cn關注吧！

These are the analysis and solutions of the specific causes when the parts of the mixing equipment are loose. If there is a fault in the process of using the mixing equipment, it must be solved in time, especially when the parts of the belt are loose. Come to our website for more information http://www.www.boy7up.cn Pay attention!