如今的全自動攪拌車已經成為眾多行業中不可缺少的一部分，是建筑工地不可缺少的設備，那么您要想更好的使用它就要在平常中提前預防好故障的出現，比如全自動攪拌車皮帶零件出現松動怎么辦呢？

Nowadays, the fully automatic mixer has become an indispensable part of many industries and an indispensable equipment for construction sites. If you want to use it better, you should prevent the occurrence of faults in advance, such as the looseness of the belt parts of the fully automatic mixer. What should you do?

全自動攪拌車電機傳動皮帶過松的情況，只需停機后調整全自動攪拌車電機傳動皮帶的張緊度即可。全自動攪拌車驅動各種物料在貯罐進行攪拌，它由取力器、萬向軸、液壓泵、液壓馬達、操縱閥、液壓油箱及冷卻裝置組成。

If the motor drive belt of the automatic mixer is too loose, just adjust the tension of the motor drive belt of the automatic mixer after shutdown. The fully automatic mixer truck drives various materials to mix in the storage tank. It is composed of power take-off, universal shaft, hydraulic pump, hydraulic motor, control valve, hydraulic oil tank and cooling device.

全自動攪拌車超載而造成攪拌軸停轉，只需調整進料量，卸出多余的物料，降低攪拌軸轉動負荷即可。

If the fully automatic mixer truck is overloaded and causes the mixing shaft to stop, it is only necessary to adjust the feeding amount, unload the excess materials and reduce the rotating load of the mixing shaft.

側葉片與關內壁卡滯物料時，在攪拌軸停轉前往往會有尖銳刺耳的摩擦聲，出現這種情況時，需立即停機檢查，人工排除異物，重新調整全自動攪拌車攪拌葉片或側葉片與罐內壁間的間隙，有必要時可以用水先清洗下。

When the materials are stuck between the side blades and the closed inner wall, there is often a sharp and harsh friction sound before the mixing shaft stops. In this case, it is necessary to stop the machine immediately for inspection, remove the foreign matters manually, readjust the gap between the mixing blades or the side blades of the automatic mixer and the inner wall of the tank, and clean it with water if necessary.

檢查V型皮帶是否過松；檢查電機皮帶輪與減速機皮帶輪是否在同一水平面上；檢查減速機皮帶輪與輸入軸的配合間隙是否過大；檢查減速空載和負載運行是否有異響判斷輸入、輸出軸軸承損壞或內部齒輪是否損壞；檢查減速機扭矩臂安裝位置是否與減速機軸線垂直；檢查驅動滾筒與減速機的同軸度；檢查小型攪拌車的軸承是否損壞。等等。

Check whether the V-belt is too loose; Check whether the motor pulley and reducer pulley are on the same horizontal plane; Check whether the fit clearance between the reducer pulley and the input shaft is too large; Check whether there is abnormal noise during deceleration no-load and load operation to judge whether the input and output shaft bearings are damaged or the internal gears are damaged; Check whether the installation position of the torque arm of the reducer is vertical to the axis of the reducer; Check the coaxiality between the drive drum and the reducer; Check whether the bearing of small mixer truck is damaged. wait.

如果大家在使用全自動攪拌車的過程中出現故障的話一定要及時的解決才行，特別是類似皮帶零件松動這種問題時才是需要及時解決的。更多相關信息獲取就來我們網站http://www.www.boy7up.cn關注吧！

If there is a fault in the process of using the automatic mixer, it must be solved in time, especially when the belt parts are loose. Come to our website for morehttp://www.www.boy7up.cn   information!