<address id="913f9"></address>

      <noframes id="913f9"><form id="913f9"><th id="913f9"></th></form>

      <address id="913f9"><address id="913f9"><nobr id="913f9"></nobr></address></address>
      <address id="913f9"><form id="913f9"><nobr id="913f9"></nobr></form></address>

      <address id="913f9"><dfn id="913f9"><listing id="913f9"></listing></dfn></address>
        <address id="913f9"><listing id="913f9"><meter id="913f9"></meter></listing></address>
        <noframes id="913f9"><form id="913f9"><nobr id="913f9"></nobr></form>

        <address id="913f9"></address>

        全國咨詢熱線

        400-879-1999

        點擊撥打服務熱線:400-879-1999
        你所在位置: 首頁 >> 新聞中心 > 公司新聞

        公司新聞

        兩種方法把攪拌車內凝結混凝土清理走

        作者:http://www.www.boy7up.cn 時間:2022-12-02

        自上料攪拌車的日常使用中,如果混凝土凝固在攪拌車里面,會很大程度上影響到自上料攪拌車的正常作業。兩種方法把攪拌車內凝結混凝土清理走,分別為:
        In the daily use of the self loading mixer, if the concrete solidifies in the mixer, it will greatly affect the normal operation of the self loading mixer. There are two methods to remove the condensed concrete in the mixer:
        方法一:
        Method 1:
        1、準備好緊急驅動軟管,將故障混凝土自上料攪拌車熄火,卸下液壓馬達上的高壓油管接頭。
        1. Prepare the emergency drive hose, turn off the faulty concrete from the loading mixer truck, and remove the high-pressure oil pipe connector on the hydraulic motor.
        2、將救援車熄火,將其液壓馬達的高壓油管卸下,并與故障車上的對應接頭用緊急驅動軟管相連。
        2. Turn off the rescue truck, remove the high-pressure oil pipe of its hydraulic motor, and connect it with the corresponding connector on the faulty truck with the emergency drive hose.
        3、發動救援車,將其操縱手柄撥至出料位置,故障車內的商品混凝土即被排出。
        3. Start the rescue truck and turn its operating handle to the discharge position, and the commercial concrete in the faulty truck will be discharged.
        4、緊急驅動完畢后,將驅動軟管卸下,并恢復兩車原狀。
        4. After the emergency drive is completed, remove the drive hose and restore the two vehicles to their original state.
        自上料攪拌車
        方法二:
        Method 2:
        1、若方法一實行有困難,則須采用以下方法,立即排出混凝土。
        1. If the method is difficult to implement, the following methods must be used to discharge the concrete immediately.
        2、在托輪和滾道之間放入木楔,以控制攪拌罐的旋轉,這時一定要注意安全。
        2. Put wooden wedges between the supporting wheel and the raceway to control the rotation of the mixing tank, and pay attention to safety at this time.
        3、將發動機熄火,拆松液壓馬達的一根高壓油管,攪拌罐可自由旋轉,控制攪拌罐的旋轉,使維修孔轉到下部,然后打開維修孔,清理出罐內混凝土。
        3. Turn off the engine, loosen a high-pressure oil pipe of the hydraulic motor, the mixing tank can rotate freely, control the rotation of the mixing tank, make the maintenance hole turn to the lower part, then open the maintenance hole, and clean out the concrete in the tank.
        4、此時一定要注意安全,商品混凝土排出完畢后,恢復自上料攪拌車原狀。
        4. At this time, attention must be paid to safety. After the commercial concrete is discharged, it shall be restored to the original state of the loading mixer truck.
        混凝土凝結在攪拌罐里面的原因有很多,除了沒有及時清洗攪拌罐外,其中主要是攪拌車發動機不能運作,沒有動力輸入液壓機而招致液壓機中止工作,使得裝料罐不能轉動而讓混凝土凝結在攪拌車罐里面,所以要及時做好清理。更多相關事項就來我們網站http://www.www.boy7up.cn咨詢!
        There are many reasons for concrete condensation in the mixing tank. In addition to the failure to clean the mixing tank in time, the main reason is that the engine of the mixer truck cannot operate, and the hydraulic machine stops working due to the lack of power input, which makes the charging tank unable to rotate and allows concrete condensation in the mixing tank. Therefore, it is necessary to clean it in time. Come to our website for more information http://www.www.boy7up.cn consulting service
        新聞中心
        聯系我們
        • 公司:萊州聚峰機械有限公司
        • 熱線:400-879-1999
        • 地址:山東省萊州市206國道與308省道交叉口東南50米

        截屏,微信識別二維碼

        国语对白在线视频