離合器摩擦片的作用就是負責把發動機的動力傳遞給傳遞齒輪，再輸出到后輪使攪拌車行駛，操作離合器片分離和結合，可以起到切斷和結合動力傳遞的作用，離合器和離合器片可以使動力更柔和，起到在發動機與車輪之間的一定的緩沖作用，使車輛平穩起步、平穩換擋和防止過載損壞發動機及傳動系統。在更換全自動攪拌車離合器摩擦片時需要注意哪些事項呢？

The function of the clutch friction plate is to transmit the power of the engine to the transmission gear, and then output it to the rear wheel to drive the mixer. The operation of the clutch plate to separate and combine can cut off and combine the power transmission. The clutch and clutch plate can make the power more flexible, play a buffer role between the engine and the wheels, and make the vehicle start smoothly Shifting smoothly and preventing overload from damaging the engine and transmission system. What should be paid attention to when replacing the clutch friction plate of the automatic mixer?

1. 從動盤總成應保持清潔，摩擦片必須防塵、防污、防油。離合器在發動機上裝配之前，要將壓盤與飛輪表面擦洗干凈、去除油污，防止造成離合器打滑。

1. The driven plate assembly shall be kept clean, and the friction plate must be dust, dirt and oil proof. Before the clutch is assembled on the engine, the surface of the pressure plate and flywheel shall be wiped clean to remove oil stains, so as to prevent the clutch from slipping.

2. 離合器在出廠之前一般都是調好的，使用中不需要調整，如果需要調整，須要使用專用的工藝器具來進行調整，防止壓盤傾斜。

2. The clutch is generally adjusted before leaving the factory, and it does not need to be adjusted during use. If it needs to be adjusted, special process tools must be used to adjust it to prevent the pressure plate from tilting.

3. 為了保持離合器工作的平穩性，離合器壓盤總成及從動盤總成在出廠之前已經進行了平衡，使用中不要隨意的拆換零件，離合器修理必須拆開時，一定要先做好記號，修理后按原記號裝配并重新平衡。

3. In order to maintain the stability of the clutch operation, the clutch pressure plate assembly and driven plate assembly have been balanced before leaving the factory. Do not randomly remove or replace parts during use. When the clutch must be disassembled for repair, make a mark first. After repair, assemble according to the original mark and re balance.

4. 在發動機上裝配或拆卸離合器時，必須對角交替打緊或放松離合器固定在飛輪上的螺栓或螺母。

4. When assembling or disassembling the clutch on the engine, tighten or loosen the bolts or nuts that fix the clutch on the flywheel diagonally.

5. 安裝離合器時，要用耐溫、耐壓的潤滑油脂適當的潤滑從動盤花鍵和變速箱1軸花鍵，保證從動盤在變速箱1軸花鍵上能自由移動，但是過量的潤滑油會引起摩擦片打滑，所以一定要注意這一點。

5. When installing the clutch, properly lubricate the driven plate spline and the gearbox 1 shaft spline with temperature resistant and pressure resistant lubricating grease to ensure that the driven plate can move freely on the gearbox 1 shaft spline, but excessive lubricating oil will cause the friction plate to slip, so be sure to pay attention to this.

6. 安裝時必須十分注意，不要損傷從動盤花鍵，防止從動盤軸向移動因毛刺卡滯而不能分離。

6. During installation, great care must be taken not to damage the spline of the driven plate to prevent the axial movement of the driven plate from being blocked due to burrs.

7. 必須保證離合器分離行程符合要求，分離行程過大，容易使分離桿碰上從動盤帶來危害，分離行程過小，將使離合器不能徹底分離。

7. It must be ensured that the clutch separation stroke meets the requirements. If the separation stroke is too large, it is easy to make the release rod touch the driven plate, which will cause harm. If the separation stroke is too small, the clutch will not be completely separated.

8. 離合器處于接合狀態時，分離軸承與分離環之間應保持2-3mm的間隙，這樣在摩擦片磨損的情況下就不會妨礙壓盤壓緊摩擦片。

8. When the clutch is engaged, the clearance between the release bearing and the release ring should be 2-3mm, so that the pressure plate will not be prevented from pressing the friction plate when the friction plate is worn.

9. 摩擦片磨損至規定磨損極限時，應及時更換從動盤總成，以免離合器打滑并劃傷壓盤及飛輪表面。

9. When the friction plate is worn to the specified wear limit, replace the driven plate assembly in time to prevent the clutch from slipping and scratching the surface of the pressure plate and flywheel.

10. 正確使用，避免操作不當引起離合器打滑。

10. Use correctly to avoid clutch slipping due to improper operation.

在攪拌車的日常使用中，要注意對離合器分離操縱機構的檢查，及時排除泵及管路的滲漏的故障，保證離合器正常工作。關注我們http://www.www.boy7up.cn了解更多事項！

In the daily use of the mixer, pay attention to the inspection of the clutch release control mechanism, and eliminate the leakage of the pump and pipeline in time to ensure the normal operation of the clutch. Follow us http://www.www.boy7up.cn Learn more!