If you feel that the engine is abnormally hot when you use the loading mixer, then at this time you must stop the car correctly and find the reason and do processing, otherwise the equipment parts will be damaged. So let's find out why.

　　當自上料攪拌車發現溫度過高或溫度過強而指示燈持續閃爍時，停機檢查水箱內的冷卻水是否變形，水箱處是否有漏水現象，水管和接頭。經標稱檢查未發現異常，可按標定補冷后繼續運行。假設行駛一段時間后，仍發現溫度過高，停車檢查后發現冷卻水量很小，多為水套內水套起泡或穿孔所致缸體。發現此類故障后，應及時修復，切不可亂。

　　When the temperature is too high or too strong and the indicator light continues to blink, stop the machine to check whether the cooling water in the water tank is deformed, whether there is water leakage at the water tank, water pipe and joint. If no abnormality is found after nominal inspection, the operation can continue after calibration cooling. Assume that after driving for a period of time, it is still found that the temperature is too high. After stopping and checking, it is found that the cooling water is very small, mostly caused by bubbling or perforation of the water jacket in the cylinder body. Such faults should be repaired in time and must not be disorderly.

　　自上料攪拌車在運行過程中，發動機內缺少冷卻液會損壞氣缸蓋密封墊并導致故障。維修后，有些司機會發現發動機容易過熱。排除發動機本身的問題，可能是水箱出現“倒水”的情況。此問題的原因之一是水箱堵塞。

　　The lack of coolant in the engine will damage the cylinder head gasket and lead to failure during the operation of self-feeding agitator. After maintenance, some drivers find their engines prone to overheating. Rule out the engine itself, may be the water tank "pouring water" situation. One cause of the problem is a blocked water tank.

　　發動機頻繁的高溫是由于氣缸體、氣缸蓋和冷卻系統其他部位的水垢和雜質脫落造成的。堵塞水箱中的散熱器通道，導致發動機冷卻系統循環不良。如果堵塞，普通的化學清潔劑很難徹底清除這些頑固的水垢。專業人士經常需要拆開水箱進行清洗，這是一個好辦法。

　　Frequent engine heat is caused by scaling and impurities peeling off the cylinder block, cylinder head and other parts of the cooling system. Blocking the radiator passage in the water tank, resulting in poor circulation of the engine cooling system. If clogged, it is difficult for ordinary chemical cleaners to completely remove the stubborn scale. Professionals often need to dismantle the water tank for cleaning, which is a good way.

　　如果攪拌車發動機經常發燙，要特別注意散熱器表面的清潔保養。散熱器表面損壞的散熱片應及時修復，保持通風。洗車時，嚴禁使用高壓水射流沖洗車面。在對水箱進行日常維護時，應使用中性清潔劑，刷洗后用清水沖洗表面。必要時用壓縮空氣吹干，安裝時檢查防蟲網。

　　If the engine of the mixer is often hot, special attention should be paid to the cleaning and maintenance of the radiator surface. The damaged heat sink on the radiator surface should be repaired in time to maintain ventilation. When washing the car, it is forbidden to use high pressure water jet to wash the car face. When undertaking daily maintenance to cistern, should use neuter cleaner, rinse surface with clean water after scrub. If necessary, dry with compressed air and check the insect proof net during installation.

　　總之，關于自上料攪拌車每次保養或進行施工之前都要對攪拌車各個系統進行檢查，畢竟系統一旦出現故障，若不及時采取修復措施，后果將不堪設想。如果您還有其它問題要解決，就來網站http://www.www.boy7up.cn咨詢吧！

　　In short, each system of the mixing truck should be checked before each maintenance or construction of the loading mixing truck. After all, once the system fails, if repair measures are not taken in time, the consequences will be unimaginable. If you have other problems to solve, please visit http://www.www.boy7up.cn!