<address id="913f9"></address>

      <noframes id="913f9"><form id="913f9"><th id="913f9"></th></form>

      <address id="913f9"><address id="913f9"><nobr id="913f9"></nobr></address></address>
      <address id="913f9"><form id="913f9"><nobr id="913f9"></nobr></form></address>

      <address id="913f9"><dfn id="913f9"><listing id="913f9"></listing></dfn></address>
        <address id="913f9"><listing id="913f9"><meter id="913f9"></meter></listing></address>
        <noframes id="913f9"><form id="913f9"><nobr id="913f9"></nobr></form>

        <address id="913f9"></address>

        全國咨詢熱線

        400-879-1999

        點擊撥打服務熱線:400-879-1999
        你所在位置: 首頁 >> 新聞中心 > 行業資訊

        行業資訊

        自上料攪拌車裝料時要注意清潔

        作者:http://www.www.boy7up.cn 時間:2022-10-07

        由于混凝土會在短時間內凝固成硬塊,且對鋼材和油漆有一定的腐蝕性,所以每次使用自上料攪拌車后,洗凈粘附在自上料攪拌車及進出料口上的混凝土是每日維護必做的,下面小編來講講相關的清潔工作。
        As the concrete will solidify into hard blocks in a short time, and has a certain corrosivity to steel and paint, it is necessary to clean the concrete adhered to the self loading mixer and the inlet and outlet every time after using the self loading mixer. The following section will talk about the relevant cleaning work.
        自上料攪拌車一般露天停放,裝料前先將罐里的積水和樹葉之類的雜物排出,以免影響混凝土質量。
        Generally, the self loading mixer is parked in the open air. Before loading, the accumulated water in the tank and sundries such as leaves shall be discharged to avoid affecting the concrete quality.
        在裝料的同時向隨車自帶的清洗用水水箱中注滿水;
        At the same time of loading, fill the water tank with water for cleaning;
        裝料后沖洗進料口,洗凈進料口附近殘留的混凝土;
        Flush the feed inlet after loading, and clean the residual concrete near the feed inlet;
        到工地卸料后,沖洗出料槽,然后向自上料攪拌車內加清洗用水30—40L;在車輛回程時保持自上料攪拌車正向慢速轉動;
        After unloading at the construction site, flush the discharge chute, and then add 30-40L of cleaning water to the charging mixer; Keep the self feeding mixer turning slowly in the forward direction when the vehicle returns;
        下次裝料前切記放掉自上料攪拌車內的污水;
        Remember to discharge the sewage from the loading mixer before the next loading;
        自上料攪拌車
        每天收工時清洗自上料攪拌車及進出料口周圍,保證不粘有水泥及混凝土結塊。
        Clean the area around the feeding mixer truck and the inlet and outlet at the end of each day to ensure that there is no cement and concrete caking.
        洗完后要關掉水箱進氣口,打開水箱排氣口排掉氣體,因為氣壓下,水管連接不好的地方,容易滲水,影響其他車輛的安全。再次檢查輪胎是否卡有石子鐵釘等雜物,使用工具及時清理,因為停車時輪胎與地面接觸的地方是檢查不到的。
        After washing, close the air inlet of the water tank and open the air outlet of the water tank to discharge the gas. Because the water pipe is not well connected under air pressure, it is easy to seep water and affect the safety of other vehicles. Check whether there are stones, nails and other sundries stuck in the tire again, and use tools to clean them in time, because the contact between the tire and the ground cannot be checked when parking.
        以上就是對自動上料攪拌車清洗維護的要點介紹,以上這些工作只要一次不認真進行,就會給以后的工作帶來很大的麻煩,所以希望大家重視自動上料攪拌車的清洗。更多相關實現就來我們網站http://www.www.boy7up.cn咨詢看看吧!
        The above is the key introduction to the cleaning and maintenance of the automatic feeding mixer. As long as these works are not carried out carefully once, they will bring great trouble to the future work. So I hope you can pay attention to the cleaning of the automatic feeding mixer. More related implementations come to our website http://www.www.boy7up.cn Consult!
        新聞中心
        聯系我們
        • 公司:萊州聚峰機械有限公司
        • 熱線:400-879-1999
        • 地址:山東省萊州市206國道與308省道交叉口東南50米

        截屏,微信識別二維碼

        国语对白在线视频