Since the use of the mixing truck is gradually expanding, so the quality and use of the product has also put forward new requirements, but some users found that the current of the equipment is too large when starting, and then some places suffered damage, what to do?

　　首先檢查自上料攪拌車各部件的完整性和清潔度，按照手冊中的說明安裝接線，確保接地裝置的安全，不要亂接。

　　First check the integrity and cleanliness of the parts of the self-feeding mixer truck, install wiring according to the instructions in the manual, ensure the safety of the grounding device, do not misconnect.

　　自上料攪拌車運行前，檢查防護罩是否松動。機器運轉時不要對設備進行檢修，以免沙子、石子等雜物落入或人為地拋入機器各運行部位，以免損壞機器設備，影響生產。

　　Check whether the protective cover is loose before the feeding mixer runs. Do not overhaul the equipment when the machine is running, so as to avoid sand, stones and other sundry objects falling or artificially thrown into the running parts of the machine, so as not to damage the machine and equipment, affecting production.

　　另外，振動篩使用完畢后，應及時將其取下收起或固定，以免人進入簡清掃時觸摸振動篩提起料斗，造成擠壓事故。如需檢修進料斗和傾卸斗下方的設備，只能在關閉機器并用螺栓支架固定料斗后進行。

　　In addition, after the use of the vibrating screen, it should be taken down or fixed in time, so as not to touch the vibrating screen hopper when entering the cleaning, resulting in extrusion accidents. Maintenance of the equipment under the feed hopper and dump hopper can only be carried out after shutting down the machine and securing the hopper with a bolt bracket.

　　在使用攪拌機的過程中，安全應該是重中之重，不要忽視任何小細節，以免發生不必要的事故。

　　In the process of using hydraulic mixer, safety should be the top priority, do not ignore any small details, so as to avoid unnecessary accidents.

　　自上料攪拌車運行時，在給料斗喂料前完全停止。使用前應檢查離合器、制動器的靈活性，鋼絲繩是否損壞及損壞程度，然后檢查保護裝置的完整性，然后進行調試。

　　When the feeder agitator is running, it stops completely before feeding the hopper. Before use should check the clutch, brake flexibility, wire rope damage and damage degree, and then check the integrity of the protection device, and then debug.

　　攪拌機軸端在高強度和高應力的工作下，使用壽命會大大降低，導致軸端漏漿。出現此問題的原因是浮動密封損壞，應更換新的浮動密封。此外，還應注意及時保養各零部件，及時更換密封件。

　　The service life of the shaft end of the mixer will be greatly reduced under high strength and high stress, resulting in slurry leakage at the shaft end. The cause of this problem is a damaged floating seal and a new floating seal should be replaced. In addition, attention should also be paid to the timely maintenance of all parts and replacement of seals in time.

　　當自上料攪拌車突然斷電或超負荷無法工作時，需要清理滾筒的剩余物料，然后檢查并修復其裝載量。自上料攪拌車用戶應進入攪拌筒進行清潔保養，并應控制電源，以防發生意外。

　　In case of sudden power failure or overload of the self-feeding agitator, it is necessary to clean the remaining material of the drum, and then check and repair its loading capacity. The user of the mixing truck should enter the mixing cylinder for cleaning and maintenance, and control the power supply to prevent accidents.

　　大家在操作自上料攪拌車的時候，會比較關注機器啟動的時間段和機器結束工作的時間段，實際上其他時間段也要對該機器進行好好的維護才是。還有問題要了解的話，就來http://www.www.boy7up.cn網站咨詢吧！

　　When we operate the feeding mixer, we will pay more attention to the time when the machine starts and the time when the machine ends work. In fact, other time periods should also be well maintained for the machine. If you still have questions to ask, go to http://www.www.boy7up.cn!