全自動攪拌車在使用之前為了確保正常的運行過程，需要對設備提前做一定檢查工作的。那么接下來就讓我們一起了解一下當設備在運行之前有哪些問題是需要我們檢查了解的。

In order to ensure the normal operation of the full-automatic mixer truck, it is necessary to check the equipment in advance. Next, let's learn what problems we need to check and understand before the equipment runs.

1、蓄電池的保養檢查：檢查蓄電池固定是否牢固。

1. Maintenance and inspection of battery: check whether the battery is fixed firmly.

2、輪胎的檢查：每月應在常溫下檢查一下輪胎氣壓。

2. Tire inspection: check the tire pressure at normal temperature every month.

3、離合器總泵液面的檢查：離合器液面介于高、低液面間則表示正常，如果低于標準線，則可能是總泵或分泵皮碗損壞。

3. Inspection of clutch master cylinder fluid level: if the clutch fluid level is between high and low, it indicates normal. If it is lower than the standard line, it may be that the master cylinder or slave cylinder cup is damaged.

4、制動液面的檢查：制動也在高、低位之間則表示正常。

4. Inspection of brake fluid level: if the brake is between high and low, it means normal.

5、發動機冷卻液液面檢查：發動機在熱機狀態時，千萬不要打開散熱器蓋，否則可能會被濺出的冷卻液或高溫蒸氣燙傷。等發動機冷卻后，檢查冷卻液的液面應處于滿位和低位之間，否則應加蒸餾水或純凈水或冷凍液，加水后的液面高度不能超過滿位。如發現短時間內冷卻液減少的很快攪拌，全自動攪拌車檢查步驟應檢查冷卻系統是否有泄漏或到維修站去檢查。

5. Check the engine coolant level: never open the radiator cap when the engine is hot, otherwise it may be scalded by the splashed coolant or high-temperature steam. After the engine is cooled, check that the liquid level of the coolant should be between the full level and the low level. Otherwise, add distilled water, purified water or freezing liquid. The liquid level after adding water should not exceed the full level. If it is found that the cooling liquid decreases rapidly in a short time, the automatic mixer shall check whether the cooling system has leakage or go to the maintenance station for inspection.

攪拌車操作流程：

Operation process of mixer truck:

1、啟動前應對機械系統各部位認真進行檢查，確認良好后方可啟動。

1. Before startup, all parts of the mechanical system shall be carefully inspected and can be started only after confirmation.

2、啟動前，應將攪拌操縱桿放在“空檔”位置。

2. Before starting, put the mixing control lever at the "neutral" position.

3、啟動后，應將攪拌操縱桿放在“卸料”位置，放去筒內積水。

3. After startup, put the mixing control lever at the "unloading" position to remove the water in the drum.

4、裝料時，攪拌操作桿應放在“裝料”位置。5、運輸前，卸料槽必須固定在“行駛”位置，防止擺動。

4. When loading, the mixing operating lever shall be placed at the "loading" position. 5. Before transportation, the discharge chute must be fixed at the "running" position to prevent swinging.

6、操作操縱桿時，應在“空檔”位置稍作停留后方可動至下一個位置。

6. When operating the control lever, you should stop at the "neutral" position for a while before moving to the next position.

8、人進入筒內清除砼結塊時，應將車輛熄火，拔下電門鑰匙，筒外設人監護。

8. When a person enters the barrel to remove concrete lumps, the vehicle shall be turned off, the switch key shall be pulled out, and a person shall be arranged outside the barrel for monitoring.

全自動攪拌車操作環境通常都不是很好，這也導致需要我們對設備在操作之前有詳細的了解才行。在確保設備不存在有任何故障問題之后才能夠操作使用設備正常運行，避免在操作中可能存在的各種不良問題。更多相關注意事項就來我們網站http://www.www.boy7up.cn咨詢吧。

The operating environment of full-automatic mixer is usually not very good, which also requires us to have a detailed understanding of the equipment before operation. The normal operation of the equipment can only be carried out after ensuring that there is no fault problem in the equipment, so as to avoid various adverse problems that may exist in the operation. For more information, please visit our website http://www.www.boy7up.cn Consult.