底盤是小型攪拌車的支撐，將起到確保機械沿規定方向行駛的重要作用，所以，一旦底盤出現故障就將導致機械的運行出現問題。那么小型攪拌車底盤系統有什么應急技巧？

　　The chassis is the support of the small mixing truck, which will play an important role in ensuring that the machine runs in the specified direction. Therefore, once the chassis failure will lead to problems in the operation of the machine. So what are the emergency skills of the small mixer chassis system?

　　小型攪拌車制動分泵漏制動液或分泵管路折斷，可在分泵管路接頭處用鐵皮、銅皮做個小墊子，將管路堵死，再旋緊螺釘，或者將斷口夾扁、卷曲堵漏，使該輪不起制動用作。但這樣做可能會造成單邊制動，駕駛時要注意安全。

　　Small agitator brake pump brake fluid leakage or pump pipe broken, can be in the pump pipe junction with iron sheet, copper make a small cushion, the pipeline is blocked, and then screw, or the fracture clamp flat, curly plugging, so that the wheel can not brake. But doing so may cause unilateral braking, so be careful when driving.

　　小型攪拌車制動總泵缺制動液，可用酒精或白酒代替，特殊情況下可用清水代替。小型攪拌車制動皮碗發漲，將發漲的皮碗放在熱水中浸泡10分鐘-20分鐘，將皮碗上的含油成分去掉，這樣就可以使皮碗恢復原來的尺寸。

　　The main brake pump of small agitator is short of brake fluid, which can be replaced by alcohol or liquor, or water in special cases. If the bowl of a small mixer is swollen, soak the bowl in hot water for 10-20 minutes to remove the oil on the bowl, so that the bowl can be restored to its original size.

　　小型攪拌車離合器摩擦片燒蝕打滑，對燒蝕不太嚴重的摩擦片，可翻面使用。如燒蝕嚴重，可用棉布或帆布數層（其厚度應與原摩擦片一致），用鋼絲或鐵絲穿過鋼片上的孔，使其固定。駕駛小型攪拌車時應做到起步平穩，換擋動作迅速。

　　Small agitator clutch friction plate ablative slip, ablative friction plate is not too serious, can be turned over to use. If the ablation is serious, several layers of cotton cloth or canvas can be used （its thickness should be consistent with the original friction sheet）， with steel wire or iron wire through the hole on the steel sheet, so that it is fixed. When driving a small mixer, it should start smoothly and shift gears quickly.

　　橫拉桿球節斷損，在保險杠或其它不影響小型攪拌車行駛的地方，卸下一只與球節總長度相似的螺釘，取代斷損的球節，裝上轉向節臂與螺母后，將螺釘露出部分用錘子鉚好。若前差速器損壞，可將小型攪拌車輪轂接合盤拆下后繼續行駛。

　　Cross tie rod ball joint broken damage, in the bumper or other places that do not affect the driving of small mixing vehicles, remove a screw similar to the total length of the ball joint, replace the broken ball joint, install the steering knuckle arm and nut, the exposed part of the screw riveted with a hammer. If the front differential is damaged, the small agitator wheel hub joint plate can be removed and continue to run.

　　基于這種認識，本文對小型攪拌車底盤系統應急技巧進行了分析，希望能夠給您有效的幫助，更多內容就來網站www.www.boy7up.cn進行咨詢吧！

　　Based on this understanding, this paper analyzes the emergency skills of the small stirring truck chassis system, hoping to give you effective help. For more information, come to www.www.boy7up.cn for consultation!