攪拌車在使用期間避免不了會出現這樣那樣的問題，比如說異常聲響問題的出現是比較常見的，那么要怎么檢查呢？我們從三個方面來進行相應的檢查工作。

　　Mixing truck can not avoid such problems during the use of such problems, such as abnormal sound problem is more common, so how to check? We will carry out the corresponding inspection work from three aspects.

　　全自動攪拌車電機故障表現

　　在分解電機前，進行空運轉，以找出問題。如機械攪拌器的電機發出異常聲響，振動很大;機械攪拌器的電機軸的軸套處發出咝咝的聲音，電機空運轉不到2分鐘軸伸溫度就達幾十度，燙守。機械攪拌器的內部軸承內圈因點蝕產生梨皮狀點蝕區域，表面粗糙，暗淡，無光澤，可明顯看到點蝕孔;骨架油封內圈破損;機械攪拌器的軸承內圈和軸套與對應的軸頸處有"跑圈"形成的暗斑。

　　Motor failure performance of fully automatic agitator

　　Before disassembling the motor, run it in the air to find problems. Such as mechanical stirrer motor abnormal sound, vibration is very large; The shaft sleeve of the motor shaft of the mechanical stirrer emits a hissing sound, and the shaft extension temperature reaches dozens of degrees in less than 2 minutes of empty operation of the motor. The internal bearing inner ring of mechanical stirrer produces pear-skin pitting area due to pitting, and the surface is rough, dull and dull, and pitting holes can be obviously seen. Skeleton oil seal inner ring damaged; There are dark spots formed by "running circle" in bearing inner ring and shaft sleeve of mechanical stirrer and corresponding journal.

　　機械密封總成故障表現

　　攪拌車容易出故障的是機械密封部分，常因磨損使機械密封失效，密封腔進水。首先分解了機械密封總成，對包括兩套機械密封，骨架油封，輸出軸，軸承，殼體及端蓋等零件進行了清洗檢查，并查驗了機械攪拌器軸承座和輸出軸的有關尺寸，如均未發現問題，說明機械密封部分完好，排除發生故障的可能性。

　　Mechanical seal assembly failure performance

　　Mixing truck is prone to failure is the mechanical seal part, often due to wear to make the mechanical seal failure, sealing cavity water. First decomposition of the mechanical seal assembly, including two sets of mechanical seal, skeleton oil seal, output shaft, bearing, shell and cover parts such as the cleaning check, and check the mechanical agitator and relevant dimensions of the output shaft bearing, such as have not found the problem, and explain mechanical seal parts in good condition, rule out the possibility of failure.

　　齒輪箱故障表現

　　有的攪拌器設備的齒輪箱加工精度較高，熱處理良好，對齒輪箱進行徹底的清洗，仔細檢查各齒輪、齒輪軸、軸承。發現輪齒表面光滑，無點蝕、交合現象，齒輪嚙合側隙正常，齒廓無明顯磨損;各軸承徑向、軸向間隙正常，內外圈及滾子表面均無點蝕斑點，整體質量良好;各軸軸向間隙合理，守盤輸出軸，活動自如，無卡殼現象，也無異常聲響。那么，可以排除齒輪箱的故障。

　　Gearbox failure performance

　　The gear box of some agitator equipment has high processing accuracy and good heat treatment. The gear box is thoroughly cleaned and the gears, gear shafts and bearings are carefully checked. It is found that the tooth surface is smooth, without pitting and mating phenomenon, the meshing backlash is normal, and the tooth profile has no obvious wear. The radial and axial clearance of each bearing is normal, and there is no spot etching on the inner and outer rings and roller surface. The overall quality is good. The axial clearance of each shaft is reasonable, keeping the output shaft of the disk, free of movement, no jamming phenomenon, no abnormal sound. Well, the gearbox can be ruled out.

　　攪拌車異常聲響問題要這樣檢查更好處理的相關內容便是這樣了，如果您在運行機器期間出現異常且您找不到問題所在的話，您可以在網站www.www.boy7up.cn聯系我們，為您解惑。

　　The abnormal sound problem of the mixer truck should be checked in this way. The related content that is better handled is this. If you run the machine abnormally and you cannot find the problem, you can contact us on the website www.www.boy7up.cn to solve your doubts.