自上料攪拌車手剎的使用率非常高，但手剎的效果會隨使用次數的增加而下降。由于平時保養不當，有時候自上料攪拌車手剎已經拉上了，卻起不到真正制動的作用，這也是車輛安全的重大隱患，所以應該定期對自上料攪拌車手剎進行維護保養。

The use rate of the hand brake of the self loading mixer truck is very high, but the effect of the hand brake will decrease with the increase of the number of uses. Due to improper maintenance at ordinary times, sometimes the hand brake of the self loading mixer truck has been turned on, but it cannot truly brake. This is also a major risk to vehicle safety. Therefore, it is necessary to regularly maintain the hand brake of the self loading mixer truck.

①進行自上料攪拌車手剎工作點位置確認

① Confirm the position of the hand brake working point of the self loading mixer truck

一般來說當自上料攪拌車手剎手柄拉到整個行程的70%時，自上料攪拌車手剎系統就應該處于正常的剎車位置。我們在日常使用中，首先應該先找出這個剎車工作點，可以通過數棘輪的響聲數量來確定，一般5格到8格之間是正常的剎車位置。

Generally speaking, when the hand brake handle of the self loading mixer truck is pulled to 70% of the entire stroke, the hand brake system of the self loading mixer truck should be in the normal braking position. In daily use, we should first identify this brake working point, which can be determined by counting the number of ratchet sounds. Generally, between 5 and 8 bars is the normal brake position.

②進行剎車效果確認

② Confirm the braking effect

把自上料攪拌車開到坡度比較大、路面狀況比較好的斜坡上，踩住車輛剎車，掛空擋，將自上料攪拌車手剎手柄拉到工作點位置。慢慢松開腳剎（注意一定要慢，保證安全），如果終自上料攪拌車沒有發生滑動，就說明自上料攪拌車手剎的效能良好。

Drive the self loading mixer truck to a slope with a relatively large gradient and good road conditions, press the vehicle brake, shift into neutral, and pull the hand brake handle of the self loading mixer truck to the working point position. Slowly release the foot brake (be careful to be slow to ensure safety). If the final self loading mixer truck does not slip, it indicates that the self loading mixer truck handbrake is effective.

③進行自上料攪拌車手剎的靈敏度測試

③ Perform sensitivity testing of the hand brake of the self loading mixer truck

選一段平坦的路面，在路面上慢速行駛，輕輕地提拉手剎手柄，感覺一下自上料攪拌車手柄的靈敏度和接合點。如果發現自上料攪拌車手剎的制動效能或靈敏度不夠理想，有經驗的司機可以自行調節手剎的剎車線，也可以將自上料攪拌車開到就近的維修站，讓維修人員幫忙調整。

Select a flat section of road and drive slowly on the road. Gently lift and pull the handbrake handle to feel the sensitivity and engagement point of the handle of the self loading mixer truck. If it is found that the braking efficiency or sensitivity of the hand brake of the self loading mixer truck is not ideal, an experienced driver can adjust the brake line of the hand brake by himself or drive the self loading mixer truck to the nearest maintenance station for assistance from maintenance personnel.

自上料攪拌車的手剎怎么進行檢查？以上就是問題的相關解答了，您對此有怎樣的疑惑或者使用需求，就來我們網站http://www.www.boy7up.cn咨詢吧！

How to check the hand brake of the self loading mixer truck? The above is the relevant answer to the question. If you have any doubts or use needs about this, please come to our website http://www.www.boy7up.cn Consult!