在我們的日常生活中，我們經常可以看到攪拌車設備的建造。它的出現給我們帶來了極大的方便。那么你知道抽檢的標準是什么嗎？讓我們從了解混音器的各種系統開始。

In our daily life, we can often see the construction of mixer equipment. Its appearance has brought us great convenience. Do you know what the sampling standard is? Let's start by understanding the various systems of the mixer.

1、氣路系統：氣泵曲軸箱油位應在油窗指示范圍內，各閥缸動作應靈活，有用管路和接口處不得漏氣，并應及時修復損壞的零件。每天應將油水分離器和儲氣罐內的水排干，油霧器應有足夠的油量。

1. Air circuit system: the oil level of the crankcase of the air pump shall be within the range indicated by the oil window, the action of each valve cylinder shall be flexible, there shall be no air leakage at the useful pipelines and interfaces, and the damaged parts shall be repaired in time. The water in the oil-water separator and air storage tank shall be drained every day, and the oil mist shall have enough oil.

2、供水系統：供水閥門開、關，故障及時排除。

2. Water supply system: the water supply valve shall be opened and closed, and the fault shall be eliminated in time.

3、傳動系統：三角帶張緊度、鏈條松緊度、聯軸節間距正常。

3. Transmission system: V-belt tension, chain tightness and coupling spacing are normal.

4、攪拌系統：自動攪拌車的攪拌葉片、門側板、襯板、攪拌臂是否短路或損壞。攪拌設備內是否有殘料，如有應及時清理。

4. Mixing system: whether the mixing blade, door side plate, lining plate and mixing arm of the automatic mixer are short circuited or damaged. Whether there is any residue in the mixing equipment, if any, it shall be cleaned in time.

5.平滑系統：在每個油嘴中加入足夠的平滑潤滑脂，重點是軸頭密封。檢查每種情況下的油位并添加足夠的潤滑脂。

5. smoothing system: add enough smoothing grease into each nozzle, with the focus on the shaft head seal. Check the oil level in each case and add sufficient grease.

6、所有地腳螺釘、雙頭調節螺釘和固定螺栓不得松脫或短接。

6. All anchor screws, double headed adjusting screws and fixing bolts shall not be loosened or short circuited.

另外，在使用時要多了解一些注意事項，例如：全自動攪拌車應設置在平放位置，前后軸應墊方木，使輪胎放置在空氣，以免啟動時走路。攪拌車應實施二次漏電保護。上班前接通電源后，必須仔細檢查，空車檢測合格后方可使用。試運行時應檢查攪拌筒的轉速是否合適。一般來說，空車的速度比汽車（充電后）略快2到3轉。若相差較大，應調整主動輪與傳動輪的比。

In addition, it is necessary to know more about some precautions during use, such as: the full-automatic mixer should be set at the flat position, and the front and rear axles should be padded with square timber to make the tires placed in the air, so as to avoid walking when starting. The mixer truck shall be provided with secondary leakage protection. Before going to work, after the power supply is connected, it must be carefully checked, and it can be used only after the empty vehicle passes the inspection. During the test run, check whether the rotating speed of the mixing drum is appropriate. Generally speaking, the speed of an empty car is 2 to 3 revolutions faster than that of a car (after charging). If the difference is large, the ratio of driving wheel to driving wheel shall be adjusted.

攪拌筒的轉動方向應與箭頭所指方向一致。如果不正確，則應更正電機接線。檢查傳動離合器和制動器是否靈活可靠，鋼絲繩是否損壞，履帶輪是否完好，周圍是否有障礙物以及各部位的潤滑情況等，開機后要時刻注意攪拌機各部分是否正常運行。停機時要經常檢查攪拌車的葉片是否彎曲，螺絲是否被敲落或松動。下班后和不使用機器時，請關閉電源并鎖好開關盒以確保安全。

The rotation direction of the mixing drum shall be consistent with the direction indicated by the arrow. If not, correct the motor wiring. Check whether the transmission clutch and brake are flexible and reliable, whether the steel wire rope is damaged, whether the crawler wheel is in good condition, whether there are obstacles around and the lubrication of each part. After starting up, always pay attention to whether each part of the mixer operates normally. During shutdown, always check whether the blades of the mixer truck are bent and whether the screws are knocked down or loosened. After work and when not using the machine, please turn off the power and lock the switch box to ensure safety.

以上就是關于攪拌車設備抽樣檢驗標準從各個系統開始的相關內容，希望以上的內容能夠對大家有所幫助，感謝您的觀看和支持，后期會整理更多資訊，您可以關注我們網站www.www.boy7up.cn。

The above is the relevant content about the sampling inspection standard for mixer truck equipment starting from each system. I hope the above content can be helpful to you. Thank you for your watching and support. More information will be sorted out later. You can follow our website www.zkzsljbc com。