一、采購的新車初駛期間都不要速度過快，速度最佳在40-60公里;而且利用發動機轉速表和車速表，使攪拌車發動機轉速和車速都在中速以下行進。
1、 When purchasing new cars, don't drive too fast. The best speed is 40-60km; Moreover, the engine speed and vehicle speed of the mixer are all below the medium speed by using the engine tachometer and speedometer.
二：攪拌車用油也要留意：攪拌車新車所運用的機油最佳用廠家指定的機油。攪拌車發動后要等幾分鐘后在行進，待水溫抵達必定的溫度后在加快。駕馭中要挑選平穩路面，最佳保持中速行進，勁量不要急加快和急剎車，油門輕踏、操作也要輕，一起還要隨時留意發動機的聲響和溫度。
2： Also pay attention to the oil used in the mixer: the oil used in the new mixer is the best oil specified by the manufacturer. After the mixer starts, it needs to wait a few minutes before moving, and it will speed up when the water temperature reaches a certain temperature. In driving, you should choose a smooth road surface, keep a medium speed, don't speed up and brake quickly, step on the accelerator lightly, operate lightly, and pay attention to the sound and temperature of the engine at any time.
三：攪拌車不要采納緊迫剎車:避免攪拌車底盤和發動機的負荷過大，所以在開始行進的幾百公里內不要加快和急剎車。如有突發狀況，要先踩下離合器踏板，在剎車
3： Don't adopt emergency braking for mixer: avoid overload of mixer chassis and engine, so don't speed up and brake abruptly in the first few hundred kilometers. If there is an emergency, first step on the clutch pedal, and then brake

四：攪拌車新車滿載會對機身車件形成損壞:在開始的一千公里內，攪拌車不要裝的太滿，等新車跑完磨合期就好了，假如滿載會使發動機繼續工作的時刻增加，形成機件磨損，新車在沒跑完磨合期不宜行進的時刻過長。
4： The full load of the new mixer will damage the parts of the fuselage: in the first 1000 kilometers, the mixer should not be too full, just wait until the new car runs through the running in period, if the full load will increase the time for the engine to continue to work, forming the wear of the parts, and the new car should not travel too long before it runs through the running in period.
五：攪拌車行車時要實時換擋:先用低擋起步，跑2里路后在換入高擋，行車中攪拌車水溫不宜過高。最佳控制在恒溫，在行進中要實時換擋，不要長時刻運用一個擋位，盡量不要運用高擋低速行進和低擋高速行進。換擋要從低轉速至高轉速要先工作一段時刻，最高轉速最佳不要高出4000轉，每個擋位的轉速都要跑到，高速狀態下要力度適中、勻稱地踏剎車踏板，直到車速下降。跑到必定公里數就要定時養護，機油要用好一點的，往后跑到必定的公里數再依據攪拌車的需要在做養護。
5： When the mixer is driving, it is necessary to shift gears in real time: start at low gear first, run for 2 miles and then shift into high gear. The water temperature of the mixer should not be too high during driving. The best control is at constant temperature. You should shift gears in real time when you are moving. Don't use one gear for a long time. Try not to use high gear and low speed or low gear and high speed. To shift gears from low speed to high speed, you need to work for a period of time first. The maximum speed should not be higher than 4000 rpm. The speed of each gear should run. At high speed, you should step on the brake pedal moderately and evenly until the speed drops. After running for a certain number of kilometers, it is necessary to maintain regularly. The engine oil should be used better. After running for a certain number of kilometers, it is necessary to maintain according to the needs of the mixer.